U-Boot 1.1.3 (Nov 7 2013 - 17:33:35) RT-AC51U bootloader version: 1.0.0.0 Board: Ralink APSoC DRAM: 64 MB ASUS RT-AC51U gpio init : wps / reset pin enable ephy clock...done. rf reg 29 = 5 SSC enabled. swing=5000, upperbound=0 ****************************** Software System Reset Occurred ****************************** Ralink SPI flash driver, SPI clock: 48MHz spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128FV raspi_read: from:30000 len:1000 Maximum malloc length: 1024 KBytes mem_malloc_start/brk/end: 0x83eaf000/83eb1000/83fb0000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.1.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Nov 7 2013 Time:17:33:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 Please choose the operation: 0: Load System code then write to Flash via Serial. 1: Load System code to SDRAM via TFTP. 2: Load System code then write to Flash via TFTP. 3: Boot System code via Flash (default). 4: Entr boot command line interface. 5: Load Boot Loader code to SDRAM via Serial. 7: Load Boot Loader code then write to Flash via Serial. 8: Load Boot Loader code to SDRAM via TFTP. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot System code via Flash. raspi_read: from:4018a len:4 RT-AC51U bootloader version: 1.0.0.0 raspi_read: from:40004 len:6 MAC Address: 1C:B7:2C:7B:42:70 raspi_read: from:40004 len:6 ## Checking 1st firmware at bc050000 ... raspi_read: from:50000 len:40 Image Name: Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3145690 Bytes = 3 MB Load Address: 80000000 Entry Point: 8000c150 raspi_read: from:50040 len:2fffda Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Giving linux ramsize: 67108864 (64 MB) Starting kernel ... [ 0.000000] Linux version 3.18.21 (vico@Vico-OpenWRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46832) ) #1 Mon Sep 28 12:30:43 CEST 2015 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Ralink MT7620A evaluation board [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0004f7f0 [ 0.000000] Readback ErrCtl register=0004f7f0 [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.080000] NET: Registered protocol family 16 [ 0.340000] PCI host bridge /pcie@10140000 ranges: [ 0.340000] MEM 0x0000000020000000..0x000000002fffffff [ 0.350000] IO 0x0000000010160000..0x000000001016ffff [ 0.360000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.370000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.370000] PCI host bridge to bus 0000:00 [ 0.380000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.380000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.390000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.390000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.400000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.400000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.410000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.410000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.420000] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.420000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.430000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.430000] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0 [ 0.440000] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 0.440000] pci 0000:01:00.1: card - bus=0x1, slot = 0x0 irq=4 [ 0.450000] Switched to clocksource systick [ 0.450000] NET: Registered protocol family 2 [ 0.460000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.460000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.470000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.470000] TCP: reno registered [ 0.480000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.480000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.490000] NET: Registered protocol family 1 [ 0.490000] rt-timer 10000100.timer: maximum frequency is 2441Hz [ 0.500000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.530000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.530000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540000] msgmni has been set to 119 [ 0.550000] io scheduler noop registered [ 0.550000] io scheduler deadline registered (default) [ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.570000] console [ttyS0] disabled [ 0.570000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A [ 0.660000] console [ttyS0] enabled [ 0.670000] bootconsole [early0] disabled [ 0.670000] bootconsole [early0] disabled [ 0.690000] m25p80 spi32766.0: found w25q128, expected en25q64 [ 0.710000] m25p80 spi32766.0: w25q128 (16384 Kbytes) [ 0.720000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.730000] Creating 4 MTD partitions on "spi32766.0": [ 0.740000] 0x000000000000-0x000000030000 : "u-boot" [ 0.750000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.760000] 0x000000040000-0x000000050000 : "factory" [ 0.770000] 0x000000050000-0x000000800000 : "firmware" [ 0.850000] gsw: setting port4 to ephy mode [ 0.860000] ralink_soc_eth 10100000.ethernet: generated random MAC address 02:99:f4:53:29:84 [ 0.870000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.890000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.900000] rt2880_wdt 10000120.watchdog: Initialized [ 0.910000] TCP: cubic registered [ 0.920000] NET: Registered protocol family 10 [ 0.930000] NET: Registered protocol family 17 [ 0.940000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.970000] 8021q: 802.1Q VLAN Support v1.8 [ 0.980000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 0.980000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 82.550000] random: nonblocking pool is initialized