U-Boot SPL 2021.10 (Nov 10 2022 - 13:29:36 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.0 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : StarFive VisionFive V2 Platform Features : medeleg Platform HART Count : 5 Platform IPI Device : aclint-mswi Platform Timer Device : aclint-mtimer @ 4000000Hz Platform Console Device : uart8250 Platform HSM Device : --- Platform Reboot Device : --- Platform Shutdown Device : --- Firmware Base : 0x40000000 Firmware Size : 360 KB Runtime SBI Version : 0.3 Domain0 Name : root Domain0 Boot HART : 1 Domain0 HARTs : 0*,1*,2*,3*,4* Domain0 Region00 : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01 : 0x0000000040000000-0x000000004007ffff () Domain0 Region02 : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address : 0x0000000040200000 Domain0 Next Arg1 : 0x0000000042200000 Domain0 Next Mode : S-mode Domain0 SysReset : yes Boot HART ID : 1 Boot HART Domain : root Boot HART Priv Version : v1.11 Boot HART Base ISA : rv64imafdcbx Boot HART ISA Extensions : none Boot HART PMP Count : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count : 2 Boot HART MIDELEG : 0x0000000000000222 Boot HART MEDELEG : 0x000000000000b109 U-Boot 2021.10 (Nov 10 2022 - 13:29:36 +0800), Build: jenkins-VF2_515_Branch_SD2 CPU: rv64imacu Model: StarFive VisionFive V2 DRAM: 8 GiB MMC: sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 B *** Warning - bad CRC, using default environment StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : StarFive Technology Co., Ltd. Product full SN: VF7110A1-2250-D008E000-00000236 data version: 0x2 PCB revision: 0xa1 BOM revision: A Ethernet MAC0 address: 6c:cf:39:00:1f:23 Ethernet MAC1 address: 6c:cf:39:00:1f:24 --------EEPROM INFO-------- In: serial@10000000 Out: serial@10000000 Err: serial@10000000 Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 Can't set block device 371 bytes read in 3 ms (120.1 KiB/s) Importing environment from mmc1 ... Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:2... libfdt fdt_check_header(): FDT_ERR_BADMAGIC Card did not respond to voltage select! : -110 ** Unable to read file ubootefi.var ** Failed to load EFI variables Scanning mmc 1:3... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 875 bytes read in 4 ms (212.9 KiB/s) U-Boot menu 1: Debian GNU/Linux bookworm/sid 5.15.0-starfive 2: Debian GNU/Linux bookworm/sid 5.15.0-starfive (rescue target) Enter choice: 1: Debian GNU/Linux bookworm/sid 5.15.0-starfive Retrieving file: /boot/initrd.img-5.15.0-starfive 9684368 bytes read in 408 ms (22.6 MiB/s) Retrieving file: /boot/vmlinuz-5.15.0-starfive 7893260 bytes read in 333 ms (22.6 MiB/s) append: root=/dev/mmcblk1p3 rw console=tty0 console=ttyS0,115200 earlycon rootw0 Retrieving file: /usr/lib/linux-image-5.15.0-starfive/starfive/jh7110-visionfivb 46706 bytes read in 12 ms (3.7 MiB/s) Uncompressing Kernel Image Moving Image from 0x44000000 to 0x40200000, end=41764000 ## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 Using Device Tree in place at 0000000048000000, end 000000004800e671 Starting kernel ... clk u5_dw_i2c_clk_core already disabled clk u5_dw_i2c_clk_apb already disabled [ 0.000000] Linux version 5.15.0-starfive (sw_buildbot@mdcsw02) (riscv64-unk2 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: StarFive VisionFive V2 [ 0.000000] earlycon: uart0 at MMIO32 0x0000000010000000 (options '115200') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, B [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id sharl [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000013fffffff] [ 0.000000] SBI specification v0.3 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10000 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 17 pages/cpu s31528 r8192 d29912 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1033735 [ 0.000000] Kernel command line: root=/dev/mmcblk1p3 rw console=tty0 console0 [ 0.000000] Unknown command line parameters: stmmaceth=chain_mode:1 selinux=0 [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 byte) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes,) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff0) [ 0.000000] Memory: 3451376K/4192256K available (9735K kernel code, 4976K rw) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 ji. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-conr [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 . [ 0.000000] random: get_random_bytes called from start_kernel+0x4d0/0x6e2 wi0 [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycs [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199s [ 0.008961] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xs [ 0.020270] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xs [ 0.031586] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xs [ 0.042896] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xs [ 0.054349] Console: colour dummy device 80x25 [ 0.060278] printk: console [tty0] enabled [ 0.064822] Calibrating delay loop (skipped), value calculated using timer f) [ 0.076031] pid_max: default: 32768 minimum: 301 [ 0.081260] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, lin) [ 0.089487] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.099376] ASID allocator disabled [ 0.103310] rcu: Hierarchical SRCU implementation. [ 0.108737] EFI services will not be available. [ 0.114074] smp: Bringing up secondary CPUs ... [ 0.120484] smp: Brought up 1 node, 4 CPUs [ 0.126110] devtmpfs: initialized [ 0.135789] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms [ 0.146635] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.167300] pinctrl core: initialized pinctrl subsystem [ 0.173833] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.180967] cpuidle: using governor menu [ 0.202141] platform 29400000.dc8200: Fixing up cyclic dependency with soc:rt [ 0.211082] platform soc:dsi-output: Fixing up cyclic dependency with 2940000 [ 0.220116] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsit [ 0.228877] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000 [ 0.246909] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.254310] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.264382] vgaarb: loaded [ 0.267563] SCSI subsystem initialized [ 0.271957] usbcore: registered new interface driver usbfs [ 0.278041] usbcore: registered new interface driver hub [ 0.283906] usbcore: registered new device driver usb [ 0.289541] mc: Linux media interface: v0.10 [ 0.294252] videodev: Linux video capture interface: v2.00 [ 0.300461] Advanced Linux Sound Architecture Driver Initialized. [ 0.307477] Bluetooth: Core ver 2.22 [ 0.311446] NET: Registered PF_BLUETOOTH protocol family [ 0.317285] Bluetooth: HCI device and connection manager initialized [ 0.324283] Bluetooth: HCI socket layer initialized [ 0.329651] Bluetooth: L2CAP socket layer initialized [ 0.335222] Bluetooth: SCO socket layer initialized [ 0.340926] clocksource: Switched to clocksource riscv_clocksource [ 0.353300] NET: Registered PF_INET protocol family [ 0.359302] IP idents hash table entries: 65536 (order: 7, 524288 bytes, lin) [ 0.370647] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 819) [ 0.380129] TCP established hash table entries: 32768 (order: 6, 262144 byte) [ 0.389183] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, lin) [ 0.398179] TCP: Hash tables configured (established 32768 bind 32768) [ 0.405641] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear) [ 0.413346] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linea) [ 0.421683] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.428385] RPC: Registered named UNIX socket transport module. [ 0.434923] RPC: Registered udp transport module. [ 0.440092] RPC: Registered tcp transport module. [ 0.445271] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.452940] PCI: CLS 0 bytes, default 64 [ 0.457784] Initialise system trusted keyrings [ 0.462851] workingset: timestamp_bits=62 max_order=20 bucket_order=0 [ 0.463048] Unpacking initramfs... [ 0.474929] NFS: Registering the id_resolver key type [ 0.480516] Key type id_resolver registered [ 0.485152] Key type id_legacy registered [ 0.489664] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.497070] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registerin. [ 0.505280] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.510487] fuse: init (API version 7.34) [ 0.546460] NET: Registered PF_ALG protocol family [ 0.551783] Key type asymmetric registered [ 0.556300] Asymmetric key parser 'x509' registered [ 0.561775] Block layer SCSI generic (bsg) driver version 0.4 loaded (major ) [ 0.569926] io scheduler mq-deadline registered [ 0.574947] io scheduler kyber registered [ 0.663244] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 c. [ 0.674445] L2CACHE: DataError @ 0x00000000.08040140 [ 0.679987] L2CACHE: DataFail @ 0x00000000.0804005B [ 0.685497] L2CACHE: No. of Banks in the cache: 8 [ 0.690693] L2CACHE: No. of ways per bank: 16 [ 0.695523] L2CACHE: Sets per bank: 256 [ 0.699763] L2CACHE: Bytes per cache block: 64 [ 0.704685] L2CACHE: Index of the largest way enabled: 15 [ 0.710998] jh7110-pmu 17030000.power-controller: registered 8 power domains [ 0.777751] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.797954] @@#########################@@ [ 0.840264] @@ dev ptr:ffffffe0bfee0000/1500/1 [ 0.845451] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers [ 0.852741] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core im [ 0.862912] [drm] Initialized pvr 1.17.6210866 20170530 for 18000000.gpu on 0 [ 0.883138] loop: module loaded [ 0.888566] libphy: Fixed MDIO Bus: probed [ 0.894711] CAN device driver interface [ 0.899561] starfive-eth-plat 16030000.ethernet: force_sf_dma_mode is ignore. [ 0.911092] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID:2 [ 0.919367] starfive-eth-plat 16030000.ethernet: DWMAC4/5 [ 0.925471] starfive-eth-plat 16030000.ethernet: DMA HW capability register d [ 0.934137] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine d [ 0.942804] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported [ 0.950298] starfive-eth-plat 16030000.ethernet: TSO supported [ 0.956765] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HWr [ 0.966024] starfive-eth-plat 16030000.ethernet: Enabled Flow TC (entries=1) [ 0.973820] starfive-eth-plat 16030000.ethernet: TSO feature enabled [ 0.980837] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width [ 1.125236] Freeing initrd memory: 9456K [ 1.383355] libphy: stmmac: probed [ 1.387134] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bu) [ 1.398094] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bu) [ 1.410314] starfive-eth-plat 16040000.ethernet: force_sf_dma_mode is ignore. [ 1.421753] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID:2 [ 1.430010] starfive-eth-plat 16040000.ethernet: DWMAC4/5 [ 1.436084] starfive-eth-plat 16040000.ethernet: DMA HW capability register d [ 1.444729] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine d [ 1.453372] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported [ 1.460847] starfive-eth-plat 16040000.ethernet: TSO supported [ 1.467289] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HWr [ 1.476525] starfive-eth-plat 16040000.ethernet: Enabled Flow TC (entries=1) [ 1.484303] starfive-eth-plat 16040000.ethernet: TSO feature enabled [ 1.491315] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width [ 1.750180] libphy: stmmac: probed [ 1.753982] YT8512B Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_a) [ 1.764276] YT8512B Ethernet stmmac-1:03: attached PHY driver (mii_bus:phy_a) [ 1.776126] Intel(R) Wireless WiFi driver for Linux [ 1.783453] cdns3-starfive 10210000.usbdrd: usb mode 2 2.0 probe success [ 1.791609] usbcore: registered new interface driver uas [ 1.797515] usbcore: registered new interface driver usb-storage [ 1.821250] starfive-rtc 17040000.rtc: registered as rtc0 [ 1.827216] starfive-rtc 17040000.rtc: setting system clock to 2001-01-01T00) [ 1.837253] i2c_dev: i2c /dev entries driver [ 1.842414] usbcore: registered new interface driver uvcvideo [ 1.849866] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=18000) [ 1.859601] Bluetooth: HCI UART driver ver 2.3 [ 1.864526] Bluetooth: HCI UART protocol H4 registered [ 1.870398] starfive-cpufreq soc:starfive,jh7110-cpufreq: Failed to get regu! [ 1.879542] starfive-cpufreq soc:starfive,jh7110-cpufreq: Failed to init stao [ 1.889794] cpuidle-riscv-sbi: idle driver registered for all CPUs [ 1.896950] sdhci: Secure Digital Host Controller Interface driver [ 1.903791] sdhci: Copyright(c) Pierre Ossman [ 1.908622] Synopsys Designware Multimedia Card Interface Driver [ 1.915544] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.922567] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel l [ 1.931713] jh7110-sec 16000000.crypto: Cannot initial dma chan [ 1.938546] usbcore: registered new interface driver usbhid [ 1.944723] usbhid: USB HID core driver [ 1.949215] usbcore: registered new interface driver snd-usb-audio [ 1.959042] NET: Registered PF_PACKET protocol family [ 1.964664] can: controller area network core [ 1.969586] NET: Registered PF_CAN protocol family [ 1.974893] can: raw protocol [ 1.978166] can: broadcast manager protocol [ 1.982817] can: netlink gateway - max_hops=1 [ 1.987931] Bluetooth: RFCOMM TTY layer initialized [ 1.993355] Bluetooth: RFCOMM socket layer initialized [ 1.999045] Bluetooth: RFCOMM ver 1.11 [ 2.003211] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.009068] Bluetooth: BNEP filters: protocol multicast [ 2.014843] Bluetooth: BNEP socket layer initialized [ 2.020489] 9pnet: Installing 9P2000 support [ 2.025278] Key type dns_resolver registered [ 2.030767] Loading compiled-in X.509 certificates [ 2.072247] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registers [ 2.081883] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registers [ 2.090841] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels [ 2.098759] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels [ 2.108143] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' al! [ 2.117320] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 22 [ 2.127546] pcie_plda 2b000000.pcie: host bridge /soc/pcie@2B000000 ranges: [ 2.135333] pcie_plda 2b000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0 [ 2.144293] pcie_plda 2b000000.pcie: MEM 0x0900000000..0x093fffffff -> 0 [ 2.153275] ATR entry: 0x0940000000 -> 0x0000000000 [0x0010000000] (param: 0) [ 2.161846] ATR entry: 0x0030000000 -> 0x0030000000 [0x0008000000] (param: 0) [ 2.170394] ATR entry: 0x0900000000 -> 0x0900000000 [0x0040000000] (param: 0) [ 2.520953] pcie_plda 2b000000.pcie: Port link up. [ 2.526380] pcie_plda 2b000000.pcie: PCI host bridge to bus 0000:00 [ 2.533318] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.539374] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 2.546976] pci_bus 0000:00: root bus resource [mem 0x900000000-0x93fffffff ] [ 2.555272] pci 0000:00:00.0: [1556:1111] type 01 class 0x078000 [ 2.561917] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0xffffffff 64bit pre] [ 2.569948] pci 0000:00:00.0: supports D1 D2 [ 2.574668] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.585355] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reg [ 2.594332] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330 [ 2.600988] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] [ 2.608553] pci 0000:01:00.0: PME# supported from D0 D3cold [ 2.617883] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.625223] pci 0000:00:00.0: BAR 0: no space for [mem size 0x100000000 64bi] [ 2.633693] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x100000000 ] [ 2.642553] pci 0000:00:00.0: BAR 8: assigned [mem 0x30000000-0x300fffff] [ 2.650038] pci 0000:01:00.0: BAR 0: assigned [mem 0x30000000-0x30000fff 64b] [ 2.658131] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.663615] pci 0000:00:00.0: bridge window [mem 0x30000000-0x300fffff] [ 2.671207] pci 0000:00:00.0: enabling device (0000 -> 0002) [ 2.677448] pci 0000:01:00.0: enabling device (0000 -> 0002) [ 2.683734] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x9d4 took 12242 us [ 2.692127] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 2.697910] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus numb1 [ 2.706512] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 q0 [ 2.716701] pcie_plda 2b000000.pcie: msi#0 address_hi 0x0 address_lo 0x190 [ 2.724677] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 2.730450] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus numb2 [ 2.738630] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 2.746302] hub 1-0:1.0: USB hub found [ 2.750476] hub 1-0:1.0: 1 port detected [ 2.755865] hub 2-0:1.0: USB hub found [ 2.760038] hub 2-0:1.0: 4 ports detected [ 2.767242] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges: [ 2.774990] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0 [ 2.783948] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0 [ 2.792936] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0) [ 2.801504] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0) [ 2.810053] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0) [ 2.970985] usb usb2-port2: over-current condition [ 3.070978] usb 1-1: new high-speed USB device number 2 using xhci_hcd [ 3.130988] usb usb2-port4: over-current condition [ 3.254392] hub 1-1:1.0: USB hub found [ 3.258784] hub 1-1:1.0: 4 ports detected [ 3.260947] pcie_plda 2c000000.pcie: Port link down, exit. [ 3.282714] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7. [ 3.305147] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH71. [ 3.316329] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMAs [ 3.327311] printk: console [ttyS0] disabled [ 3.352462] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 16, base_baud =A [ 3.362309] printk: console [ttyS0] enabled [ 3.362309] printk: console [ttyS0] enabled [ 3.371119] printk: bootconsole [uart0] disabled [ 3.371119] printk: bootconsole [uart0] disabled [ 3.382626] i2c 2-0045: Fixing up cyclic dependency with 295d0000.mipi [ 3.390298] at24 5-0050: supply vcc not found, using dummy regulator [ 3.397510] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write [ 3.406257] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900V [ 3.415684] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:180V [ 3.425255] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900V [ 3.434688] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 V [ 3.443494] i2c 6-0010: Fixing up cyclic dependency with 19800000.vin_sysctl [ 3.451047] imx219 6-0010: supply VANA not found, using dummy regulator [ 3.457845] imx219 6-0010: supply VDIG not found, using dummy regulator [ 3.464561] imx219 6-0010: supply VDDL not found, using dummy regulator [ 3.478762] imx219 6-0010: failed to read chip id 219 [ 3.484070] imx219: probe of 6-0010 failed with error -5 [ 3.489690] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter! [ 3.497744] jh7110-vin 19800000.vin_sysctl: stfcamss probe success! [ 3.507037] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mod. [ 3.507375] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mod. [ 3.514337] dwmmc_starfive 16010000.sdio0: Using internal DMA controller. [ 3.521568] dwmmc_starfive 16020000.sdio1: Using internal DMA controller. [ 3.528338] dwmmc_starfive 16010000.sdio0: Version ID is 290a [ 3.535131] dwmmc_starfive 16020000.sdio1: Version ID is 290a [ 3.535159] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 29,32 bio [ 3.540904] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 28,32 bio [ 3.540963] jh7110-sec 16000000.crypto: Unbalanced pm_runtime_enable! [ 3.541095] jh7110-sec 16000000.crypto: will run requests pump with realtimey [ 3.542923] jh7110-sec 16000000.crypto: Initialized [ 3.543422] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported [ 3.543522] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin [ 3.543528] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 71 [ 3.543597] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 3.543604] sf-mipi-dphy-tx 295e0000.mipi-dphy: GET_AON_GP_REG [ 3.543609] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 3.543616] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, ur [ 3.544395] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end [ 3.545202] of_cfs_init [ 3.545223] of_cfs_init: OK [ 3.545554] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac3 [ 3.545796] cfg80211: Loading compiled-in X.509 certificates for regulatory e [ 3.546735] mmc_host mmc1: card is polling. [ 3.556447] mmc_host mmc0: card is non-removable. [ 3.658142] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.679534] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xfff) [ 3.688939] platform regulatory.0: Direct firmware load for regulatory.db fa2 [ 3.697590] cfg80211: failed to load regulatory.db [ 3.701257] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registereds [ 3.712461] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done. [ 3.719000] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xfffff) [ 3.727140] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000 [ 3.733066] seeed_panel 2-0045: Unknown Atmel firmware revision: 0x00 [ 3.739544] cdns-dsi 295d0000.mipi: ====starfive_dsi_bind end [ 3.745306] starfive soc:display-subsystem: bound 295d0000.mipi (ops 0xfffff) [ 3.753415] vs-simple-encoder soc:rgb-output: encoder_bind begin [ 3.759434] no panel, -19 [ 3.762072] vs-simple-encoder soc:rgb-output: encoder_bind error [ 3.768081] starfive soc:display-subsystem: bound soc:rgb-output (ops 0xffff) [ 3.776275] vs-simple-encoder soc:dsi-output: encoder_bind begin [ 3.782305] no panel, -517 [ 3.785018] vs-simple-encoder soc:dsi-output: encoder_bind error [ 3.790939] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000) [ 3.791032] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffff) [ 3.791455] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsys1 [ 3.881056] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000) [ 4.072270] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 500000) [ 4.083194] mmc1: new high speed SDXC card at address aaaa [ 4.089811] mmcblk1: mmc1:aaaa SN64G 59.5 GiB [ 4.099543] random: fast init done [ 4.106802] GPT:Primary header thinks Alt. header is not at the end of the d. [ 4.114227] GPT:30719999 != 124735487 [ 4.117902] GPT:Alternate GPT header not at the end of the disk. [ 4.123943] GPT:30719999 != 124735487 [ 4.127626] GPT: Use GNU Parted to correct GPT errors. [ 4.132870] mmcblk1: p1 p2 p3 [ 4.140940] usb 1-1.2: new low-speed USB device number 3 using xhci_hcd [ 4.293719] input: Logitech USB Keyboard as /devices/platform/soc/2b000000.p0 [ 4.341000] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000) [ 4.371497] hid-generic 0003:046D:C31C.0001: input: USB HID v1.10 Keyboard [0 [ 4.393330] input: Logitech USB Keyboard Consumer Control as /devices/platfo1 [ 4.471080] input: Logitech USB Keyboard System Control as /devices/platform2 [ 4.488038] hid-generic 0003:046D:C31C.0002: input: USB HID v1.10 Device [Lo1 [ 4.781026] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000) [ 5.230999] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000) [ 5.271029] usb 1-1.1: new full-speed USB device number 4 using xhci_hcd [ 5.423763] input: Logitech USB Receiver as /devices/platform/soc/2b000000.p3 [ 5.439714] hid-generic 0003:046D:C52F.0003: input: USB HID v1.11 Mouse [Log0 [ 5.457870] input: Logitech USB Receiver Consumer Control as /devices/platfo4 [ 5.541021] hid-generic 0003:046D:C52F.0004: input: USB HID v1.11 Device [Lo1 [ 5.850962] ALSA device list: [ 5.853939] #0: Starfive-Multi-Sound-Card [ 5.862572] Freeing unused kernel image (initmem) memory: 2188K [ 5.868850] Run /init as init process Loading, please wait... Starting version 251.2-5 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... 1;-1fdone. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 8.106286] EXT4-fs (mmcblk1p3): 1 orphan inode deleted [ 8.111588] EXT4-fs (mmcblk1p3): recovery complete [ 8.128607] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data mode. . done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 8.774538] systemd[1]: System time before build time, advancing clock. [ 8.861896] systemd[1]: systemd 251.2-5 running in system mode (+PAM +AUDIT ) [ 8.893945] systemd[1]: Detected architecture riscv64. Welcome to 8.901345] systemd[1]: Hostname set to . 1mDebian GNU/Linux bookworm/sid! [ 9.417167] systemd[1]: Queued start job for default target Graphical Interf. [ 9.426822] systemd[1]: Created slice Slice /system/getty. [ OK 9.433208] systemd[1]: Created slice Slice /system/modprobe. 0m] Created slic[ 9.440386] systemd[1]: Created slice Slice /system/serial-g. e Slice[ 9.447651] systemd[1]: Created slice User and Session Slice. /system/getty 9.454598] systemd[1]: Started Forward Password Requests to Wa. 0m. [ [ 9.463539] systemd[1]: Arbitrary Executable File Formats File System Aut. OK ] Create[ 9.481054] systemd[1]: Reached target Local Integrity Protected. d slice 9.489153] systemd[1]: Reached target Remote File Systems. mSlice /system/m[ 9.496055] systemd[1]: Reached target Slice Units. odprobe. [[ 9.502295] systemd[1]: Reached target Swaps. OK 9.508066] systemd[1]: Reached target Local Verity Protected Volumes. m] Created slice Slice [ 9.517131] systemd[1]: Listening on Syslog Socket. /system/serial-g[ 9.523731] systemd[1]: Listening on initctl Compatibility N. etty. [ OK ] Created slice User and Session Slice 9.537601] systemd[1]: Journal . m. [ O[ 9.549551] systemd[1]: Listening on Journal Socket (/dev/log). K ] Started[ 9.556836] systemd[1]: Listening on Journal Socket. Forwar[ 9.563228] systemd[1]: Listening on udev Control Socket. d Password R…u[ 9.569803] systemd[1]: Listening on udev Kernel Socket. ests to Wall Directory Watch[ 9.578123] systemd[1]: Mounting Huge Pages File. . [ OK ] Reached [ 9.586283] systemd[1]: Mounting POSIX Message Queue File S. target Local Integrity [ 9.595426] systemd[1]: Mounting Kernel Debug File Sy. Protected Volume[ 9.602339] systemd[1]: Kernel Trace File System was skipped. s. [ 9.616206] systemd[1]: Create List of Static Device Nodes was skipped becau. m OK ] Reached target 9.635382] systemd[1]: Starting Load Kernel Module c. 1;39mRemote File Systems. [ 9.644112] systemd[1]: Starting Load Kernel Module drm... [ OK ] Reached targ[ 9.652233] systemd[1]: Starting Load Kernel Module fus. et Slice Units. [ OK ] Reached targe[ 9.662515] systemd[1]: Starting Journal Service... t Swaps. [ OK ] Reached target Local Verity[ 9.674254] systemd[1]: Starting Load Ke. Protected Volumes. [ 9.683236] systemd[1]: Starting Remount Root and Kernel File Systems... 2m OK ] Li[ 9.690563] systemd[1]: Repartition Root Disk was skipped becaus. stening on Syslog Socke[ 9.703237] systemd[1]: Starting Coldplug All udev De. t. [ OK ] Listening on initctl Compa[ 9.713892] systemd[1]: Mounted Huge Page. tibility Named P[ 9.721059] systemd[1]: Mounted POSIX Message Queue File Sys. ipe. [ 9.728391] systemd[1]: Mounted Kernel Debug File System. 32m OK ] L[ 9.735551] systemd[1]: modprobe@configfs.service: Deactivated s. istening on 9.743254] systemd[1]: Finished Load Kernel Module configfs. 1;39mJournal Socket (/dev/log). [ OK ] Listening on Journal Socket 9.756948] systemd[1]: modprobe@drm.serv. 0m. [ [ 9.765354] systemd[1]: Finished Load Kernel Module drm. OK ] Listen[ 9.772341] systemd[1]: modprobe@fuse.service: Deactivated succe. ing on [ 9.779933] systemd[1]: Finished Load Kernel Module fuse. udev Control Soc[ 9.786772] systemd[1]: Started Journal Service. ket. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Starting Load Kernel Module configfs... Starting Load Kernel Module drm... Starting Load Kernel Module fuse... Starting Journal Service... Starting 9.836678] systemd-journald[257]: Received client request . mLoad Kernel Modules... Starting Remount Root and Kernel File Systems... Starting Coldplug All u[ 9.857387] systemd-journald[257]: File /var. dev Devices... [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. [ OK ] Reached target Local File Systems. Starting Tell Plymouth To Write Out Runtime Data... Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Tell Plymouth To Write Out Runtime Data. [ OK ] Finished Coldplug All udev Devices. Starting Helper to synchronize boot up for ifupdown... [ OK ] Finished Helper to synchronize boot up for ifupdown. Starting Raise network interfaces... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Show Plymouth Boot Screen... [ OK ] Finished Raise network interfaces. [ OK ] Reached target Network. [ OK ] Started Show Plymouth Boot Screen. [ 10.650892] jpu: loading out-of-tree module taints kernel. [ 10.652699] vdec: loading out-of-tree module taints kernel. [ 10.657515] cnm_jpu 13090000.jpu: init device. [ 10.662195] systemd-journald[257]: Oldest entry in /var/log/journal/e593f8ed. [ 10.663560] SUCCESS alloc_chrdev_region [ 10.664366] vdec 130a0000.vpu_dec: device init. [ 10.664377] SUCCESS alloc_chrdev_region [ 10.721721] systemd-journald[257]: /var/log/journal/e593f8ed757a4b42a5589c96. [ OK ] Found device /dev/ttyS0. [ OK ] Started Network Time Synchronization. [ OK ] Found device /dev/hvc0. [ 11.627034] random: alsactl: uninitialized urandom read (4 bytes read) [ OK ] Started Forward Password R…s to Plymouth Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Reached target Path Units. [ OK ] Reached target System Time Set. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Started ifup for eth0. [ OK ] Started ifup for eth1. [ OK ] Reached target System Initialization. [ 11.906943] random: alsactl: uninitialized urandom read (4 bytes read) m OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Daily dpkg database backup timer. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard u[ 11.945297] random: dbus-daemon: uninitialized ura) nused blocks once a week. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily man-db regeneration. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting Save/Restore Sound Card State... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Regular background program processing daemon. Starting D-Bus System Message Bus... Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting System Logging Service... Starting OpenBSD Secure Shell server... Starting User Login Management... Starting Permit User Sessions... Starting Disk Manager... [ OK ] Finished Save/Restore Sound Card State. [ OK ] Reached target Sound Card. [ OK ] Finished Permit User Sessions. Starting Light Display Manager... Starting Hold until boot process finishes up... [ 12.090978] random: crng init done [ 12.095729] random: 1 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started System Logging Service. [ 12.478135] starfive-eth-plat 16030000.ethernet eth0: PHY [stmmac-0:00] driv) [ 12.489582] starfive-eth-plat 16030000.ethernet eth0: Register MEM_TYPE_PAGE0 [ 12.501007] dwmac4: Master AXI performs fixed burst length [ 12.506533] starfive-eth-plat 16030000.ethernet eth0: No Safety Features supd [ 12.514559] starfive-eth-plat 16030000.ethernet eth0: IEEE 1588-2008 Advanced [ 12.523691] starfive-eth-plat 16030000.ethernet eth0: configuring for phy/rge [ OK ] Started 12.536923] starfive-eth-plat 16040000.ethernet eth1: PHY [s) 1;39mD-Bus System Message Bus. [ O[ 12.552092] starfive-eth-plat 16040000.ethernet eth1: Register MEM_TYPE_0 K ] Started[ 12.560614] dwmac4: Master AXI performs fixed burst length User L[ 12.567224] starfive-eth-plat 16040000.ethernet eth1: No Safety Featud ogin Management 12.576495] starfive-eth-plat 16040000.ethernet eth1: IEEE 1588d [0m. [ OK ] Start[ 12.586796] starfive-eth-plat 16040000.ethernet eth1: configure ed Avah[ 12.592041] starfive-eth-plat 16040000.ethernet eth1: Link is Up - 10f i mDNS/DNS-SD Stack. Starting Load Kernel Module drm... [ OK ] Finished Load Kernel Module drm. [ 13.076802] vs_gem_dumb_create size = 1000 [ 13.080976] Allocated coherent memory, vaddr: 0xFFFFFFE0FEBF6650, paddr: 0x10 [ 13.088733] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0 [ 13.453455] PVR_K: 433: RGX Firmware image 'rgx.fw.36.50.54.182' loaded [ 13.536919] PVR_K: 433: Shader binary image 'rgx.sh.36.50.54.182' loaded [ 13.549216] PVR_K: 433: X connected - (devID = 0) [ 13.825476] vs_gem_dumb_create size = 7e9000 [ 13.830368] Allocated coherent memory, vaddr: 0xFFFFFFE0FCFC4000, paddr: 0x80 [ 13.838054] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0 [ 13.876700] vs_gem_dumb_create size = 4000 [ 13.880955] Allocated coherent memory, vaddr: 0xFFFFFFE0FCFC09C0, paddr: 0x80 [ 13.888612] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0 [ 13.894379] vs_gem_dumb_create size = 4000 [ 13.898559] Allocated coherent memory, vaddr: 0xFFFFFFE0FCFC0AA0, paddr: 0x80 [ 13.906233] ====> vs_gem_alloc_buf, 162.vs_obj->get_pages = 0 Debian GNU/Linux bookworm/sid starfive hvc0 starfive login: Debian GNU/Linux bookworm/sid starfive ttyS0 starfive login: [ 14.978313] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_c0 [ 14.987819] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 14.997656] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 15.007501] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.016389] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi9 [ 15.025272] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.034499] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.043726] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.052953] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.062181] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi2 [ 15.071411] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi2 [ 15.080634] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi2 [ 15.089862] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 15.099270] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 15.108243] innohdmi-starfive 29590000.hdmi: ******************************** [ 15.117384] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 15.127305] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.136280] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi0 [ 15.145259] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi1 [ 15.154321] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi3 [ 15.163729] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi3